View LB1966_182555.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : EN6215
LB1966M
Monolithic Digital IC
LB1966M
Fan Motor 2-Phase Half-Wave Driver
Features
Package Dimensions
* Dual power supply voltage design (5/12V) and wide voltage unit: mm 3086A-MFP10S handling range * Built-in Hall amplifier with hysteresis (supports core without commutating pole) * Built-in lockup protection and automatic recovery circuits 10 (External capacitor for rotation detection need only be 0.1 F, allowing compact, cost-saving design) * Built-in latch-type RD (restraint protection) output (Vosat = 0.2Vtyp at Io = 5 mA) * Built-in output transistor with output withstand voltage 1 24Vmin/output current 500 mA (average), 1.2A (peak) 5.1 * Built-in thermal protection circuit * Compact, high-temperature resistant MFP-10 package reduces external parts count and mounting space, therefore 0.35 making this IC support the motors with a wide range of sizes and speeds.
[LB1966M]
0.625 1.8 max
0.15 0.55 SANYO : MFP10S
6
5
1.0
Specification
Absolute Maximum Ratings at Ta = 25C
Symbol Conditions VCC max Pd max With specified substrate * IOUTave IOUTpeak t 1 ms Output withstand voltage VOUT max RD output current IRD max RD output withstand voltage VRDOUT max Operating temperature Topr Storage temperature Tstg * With substrate (114.3 x 76.1 x 1.5 mm3, glass epoxy) Parameter Maximum supply voltage Allowable power dissipation Output current Ratings 18 800 500 1200 Internal 10 18 -30 to +85 -55 to +150 Unit V mW mA mA V mA V C C
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
63099RM(KI) No. 6215-1/4
0.1 1.5
5.15 6.4
4.4
LB1966M
Allowable Operating Ranges at Ta = 25C
Parameter Power supply voltage Common mode input voltage range Symbol VCC1 VCOM Conditions Ratings 3.6 to 17 0.2 to VCC-2.3 Unit V V
Electrical Characteristics at Ta = 25C, VCC = 12V
Parameter Circuit current CT capacitor charge current Capacitor discharge current Capacitor discharge current ratio CT charge voltage CT discharge voltage Output limiter withstand voltage Output saturation voltage Hall input sensitivity RD output saturation voltage RD output leak current Thermal protection trigger temperature Symbol ICC ICT1 ICT2 RCT VCT1 VCT2 VOLM VOsat VHN VRDsat IRDL TTSD Conditions In drive mode (CT = L) In lockup protection mode (CT = H) VCT = 0.2V VCT = 8V RCT = ICT1/ICT2 min Ratings typ 4 4 1.2 0.24 6.0 7.0 1.6 25.5 1.0 10 0.2 0.1 180 max 6 6 2.0 0.4 8.0 8.0 2.0 27.0 1.3 18 0.5 10 200 Unit mA mA A A - V V V V mV V A C
Io = 10 mA Io = 500 mA Including offset and hysteresis IRD = 5 mA VRD = 14V Assured design target *
0.8 0.16 4.0 6.0 1.2 24.0
150
* Assured design target: Target value, not measured individually
Truth Table
IN- H L - IN+ L H - CT L H OUT1 L H off OUT2 H L off RD L L H Mode Rotating Lock-up protection activated
Pin Assignment
RD 1 IN+ 2
10 VCC
9
CT
NC 3
LB1966M
8
NC
IN- 4
7
OUT2
OUT1 5
6
GND
Top view
No. 6215-2/4
LB1966M
Sample Application Circuit 5/12V power supply (3.8 to 17V)
VCC
OUT1 H IN+
IN-
OUT2
RD CT 0.1F GND
On-board parts
Precautions * Wiring layout for IN- and OUT1 must be designed to prevent interference. (If oscillation occurs for example when output phase is switched, connect a capacitor with 0.1 F or less between IN- and IN+ pins.) * If CT pin is connected to GND, the lockup protection and restart functions are disabled. * In a circuit configuration as shown above, a power supply/GND reverse connection will cause a current to flow as follows: GND -> OUT -> coil -> power supply. The magnitude of this current is limited by the coil resistance. If it is less than 500 mA, the IC will not be destroyed. If required, insert a diode between VCC and the coil.
No. 6215-3/4
LB1966M
Block Diagram and Sample Application Circuit
Thermal protection circuit VCC
L1
L2
OUT1
IN+ Control block IN- H
OUT2
RD
Constant current source CT C1
0.1 to 1F GND
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of June, 1999. Specifications and information herein are subject to change without notice. PS No. 6215-4/4

▲Up To Search▲

Price & Availability of LB1966

	To Download LB1966 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .